Carburetor Operation Principles
Engine fuel and air feed systems
One type of feed system adopted for internai combustion engines is schematically
shown in
Fig. 1 where the
feed stages are:
- Air feed: air is drawn in by the engine through an air cleaner (or filter).
- Fuel feed: fuel is sucked from tank and delivered to carburation area by an engine-operated mechanical lift pump.
- Fuel/air mixture: is handled by the carburettor which governs the power produced by the engine through its throttle valve.
- Mixture delivery to cylinders: through the intake manifold.
What the carburettor does
The carburettor is assigned the task of blending a combustible mixture of air and fuel in the correct proportions
to meet the variable requirements of the engine. The mixture supplied must have a given metering and be as uniformly
blended as possible. The metering value, or mixture strength a, is given by the weight ratio between the amounts of
air and fuel drawn in by the engine.
For the normally available gasolines the correct mixture strength, that is,
without any excess of either component, consists approximately
15 kg of air to
1 kg of gasoline, briefly known as
strength 15.
Engines may work satisfactorily with trong mixtures (excess fuel) down to around strength
and with lean mixtures (excess air) up to around
strength 18. By optimum
blend is intended a mixture in
which air and fuel are as intimately and uniformly oalesced as possible, with the state of fuel changed from
liquid into vapour.
Engine mixture metering requirements
Fig. 2 shows the
influence of fuel/air mixture strength n the erformance of a modern engine,
considered at a random point in engine operation under average service
range conditions. A slightly strong or rich mixture
ratio gives the maximum power obtainable from the engine whereas a slightly
lean or weak ratio gives the best economy (low specific fuel consumption).
Engine operation range
An automobile engine operates under the most diverse speed (rpm) rate and power
output conditions. Some of the
more significant service conditions are discussed below with the aid of Figures
3-
4-
5.
Fig. 3 - Full power:
carburettor throttle is held wide open.
Fig. 24 -
Partial power or part load: the throttle is opened progressively.
Generally, this condition refers to the power required to move the car at a
steady speed on level road, with transmission in direct drive or highest gear
ratio, from the lowest to the highest speed. The complete curve - plotted with engine
on dynamometric test bench - starts with carburettor throttle in minimum opening
position and ends, through progressive setting variations, with throttle wide open.
Fig. 5 -
Pick-up or acceleration: the throttle is suddenly set to an opening
wider than it had before and the engine must rapidly increase its rotational speed.
This is accomplished properly
if mixture strength a attains the value needed for full power operation; now, if the specified value is exceeded,
pick-up will be poor owing to excessive mixture richness whereas if mixture strength is below the value specified
for optimum part load operation engine "stutter" (or flat spots) will result because of excessive mixture weakness.
Idle (or slow running) speed: throttle is almost totally
closed and allows the engine to operate at the minimum
speed at which it will keep running but without producing any power for work.
In
Fig. 4 idle speed rates are reached below 1000 rpm of engine.
In
Fig. 5 the depression (vacuum) and mixture strength curves at part load
operation begin at engine idle speed.
As the set of graphs provide the curve patterns for power, throttle setting, specific fuel consumption, mixture
strength a and manifold vacuum, a good idea may be had of what the engine requirements actually are.
In brief, a strong or rich mixture is needed for full power, pick-up and extreme rpm rates while a lean
or weak mixture is needed for best economy at limited power outputs.
The Simple Spray Carburettor
It is shown in
Fig. 6 and consists of:
- A fuel bowl or chamber V in which a float-controlled needle valve keeps
the fuel constantly at a level 5-6 mm lower than the fuel in jet G.
- A Venturi D.
- A spray tube or nozzle S through which fuel flows from float chamber to
calibrated jet G.
- A throttle F generally of the butterfly valve type which regulates the
amount of fuel/air mixture drawn in by the engine.
The purpose of Venturi
D is to increase the
depression acting on jet
G to favour the
vapourisation of the gasoline sprayed from the jet during engine operation:
this occurs because of the physical laws illustrated in
Fig. 7.
The manometer connected to the Venturi restriction indicates the lowest
pressure (highest vacuum) referred to the atmosphere: jet
G is located in this area and delivers
fuel sucked from the float chamber which is kept at atmospheric pressure
through vent
A.
Fundamental carburettor systems
Carburettor designs may have barrel arrangements different from the simple spray
unit of
Fig. 6: three basic
patterns are shown in
Fig. 8.
1 - Downdraft (or inverted) carburettor: air enters from the top.
It is practically the standard pattern on the majority of current automobiles because it is
more accessible and provides better engine feed as the mixture flow is assisted by gravity.
2 - Updraft (or vertical) carburettor: air enters from the bottom.
Largely adopted in the past because it avoided admission of fuel in the liquid state to the engine.
Abandoned in current applications because it is not easily accessible and fails to
ensure proper cold starting and cylinder charge volumetric efficiency.
3 - Sidedraft (or horizontal) carburettor: air enters from the side.
Preferred when low under-hood height is a design requirement.
Also used are some intermediate patterns with inclined barrels.
Simple spray carburettor defects
a) Considering the physical laws governing the
discontinuous efflux of fluids (both liquid and gaseous)
from restricted apertures, it becomes possible to show that as the vacuum in
the Venturi increases the amount of fuel issuing from the pilot jet will also
increase but at a faster rate than the increase in the air swallowed in by the
carburettor.
The mixture formed in a simple carburettor becomes noticeably,
richer as the engine draws in larger amounts of air; as a net result, the
mixture will be correctly proportioned at greater air flow rates but too lean
at lower flow rates. The simple spray carburettor, as considered here, also
has the following failings:
b)
It does not permit engine operation under no-load conditions as it has no
idle speed or slow running device.
During this stage, the depression in Venturi is too weak to draw any fuel
via spray tube S -
Fig. 6.
c) It cannot meet sudden engine rpm rate
variations as it has no transition (or progression) orifice system or
accelerating devices.
d)
It does not allow cold starting of the engine as the depression in Venturi
drops stili further on account of the lower cranking speed supplied by the
starter motor while the engine needs a rich mixture; in other words, it is
not equipped with a starting device or choke.
All these shortcomings are
obviated by special features incorporated in modern carburettors.
The Modern Carburettor
To prevent the mixture strength from enrichening as the demand of engine increases,
several provisions have been devised over the past 70 years one of the most suitable
of which is the "air bleed correction" system, being automatic and without moving
mechanical parts.
a) Air bleed correction
This feature was adopted on Weber carburettors and is illustrated in
Fig. 9.
When a depression is established in the restriction of Venturi
D it communicates
with well
P through spray tube
S, fuel is drawn out through jet
G while outside air, via
jet
Gf, "bleeds" in through the lateral holes
in emulsion tube
T.
As the vacuum becomes stronger, following the increase in engine rpm rate, the
fuel issuing from jet
G is corrected by the
increasingly higher "braking" action
of the air drawn in through jet
Gf
and the orifices in emulsion tube
T.
The main advantages of this automatic corrective bleeding action are:
-
Better atomisation of fuel because spray tube S does not supply only
gasoline, as occurs with the simple spray carburettors, but a suitably
proportioned fuel/air mixture.
- As may be readily seen, jet G is no longer
submitted to the full action of the vacuum in Venturi D
whereby to a given fuel flow rate corresponds a larger sized jet
G. The advantages offered by this arrangement
are twofold: firstly, a larger size jet is easier to make and is less
affected by possible impurities in the fuel; secondly, its efflux characteristics
contribute to mixture correction improvement.
Also of great importance is the size of spray tube
S
and of the space between emulsion tube
T and well
P where the fuel flows: in fact, the reduced size
of tube
S and of the cavity around
T means stronger resistance to the passage of the
mixture, namely, the higher the vacuum in Venturi the higher the resistance or
"braking" action.
By varying also these two design features, the fuel supply curve can be further
corrected thus obtaining the best possible mixture metering for proper engine feed.
b) Idle speed (or slow running) device
The idie speed device allows a warm engine to operate at the lowest rpm rate at
which it will keep running. Under this condition, the throttle is nearly closed
and the degree of vacuum promoted in the Venturi is inadequate to draw out any
fuel from the nozzle, owing to the small amount of air breathed in by the engine.
Now, going back to
Fig. 5,
it may be seen how the vacuum in induction manifold
is higher at lower air flow rates under part-load operation which, as mentioned
earlier, at one end approaches the idling speed stage.
This low vacuum is therefore
exploited for the idling engine feed circuit by connecting the throat area
downstream of the throttle to a fuel jet
Gm
,
Fig. 10, which is by-passed by an
air corrector jet
Gam that also cuts-out the
syphoning action which would otherwise be present.
The mixture thus formed is drawn in via orifice 1 whose bore is varied by a
taper-pointed screw
3, hence called
"idle mixture adjusting screw". During idle
the engine breathes the air it needs through the small gap around the throttle
valve: This gap is varied by a specially provided
"idle speed adjusting screw" 4.
Two adjusting screws are thus provided for mixture and speed rate variations
ensuring proper idle operation settings. In the more common applications, the
idle speed circuit fuel is taken from the main system well at
a given location which generally is level with the lower holes of emulsion
tube - as shown in
Fig. 10
- or, at any rate, downstream of the main or pilot
jet.
This arrangement ensures the automatic exclusion of the idle speed circuit
feed when it is not needed. For instance, under full power operation - when the
depression in well is highest - a "reversal" may occur in the idle speed circuit,
that is, air enters through orifices
1
and
2, jet
Gam and flows to the main well.
In some sports car designs the idle speed circuit is often fed directly from the
float chamber; in others, said "reversal" is limited by varying the idle speed
system.
c) Acceleration progression
As described so far, the carburettor can operate equally well at both idle
and normal speeds, with part- or wideopen throttle. However, if the throttle is
opened slightly from its idle setting to rev up the engine, a"stalling" results
and engine will stop.
This occurs because the wider gap around throttle lets in a greater amount
of air while the mixture issuing from the taper-pointed screw orifice instead
of increasing proportionally tends to reduce with the decreasing depression:
the engine thus receives an excessively lean mixture, is "starved" and stops.
To ensure a progressive action during acceleration a transition orifice
2 is drilled in carburettor, directly in line
with the upper edge of the throttle in its idle speed setting and
communicating with the idle mixture duct -
Fig. 11.
During idle speed operation - see A,
Fig. 11 - the transition orifice being
2
located upstream of the throttle valve where pressure is almost the same as
atmospheric, air is introduced into the barrel with the mixture issuing
from orifice
1 below.
When the throttle opening is increased - see
B,
Fig. 11 - transition
orifice
2 will be located partially or totally
in the area downstream of the throttle where vacuum is rather high and will
thus supply the mixture in parallel with idle speed orifice
1.
If at this point the throttle is further
opened the mixture supplied by the idle speed circuit alone would no longer
be adequate but, now, the depression acting upon nozzle
S is sufficient to draw a spray of fuel from it.
- see C,
Fig. 11.
In some cases two or three transition orifices are provided to prolong the
progression stage accompanying the opening of the throttle valve.
During these progressive acceleration stages,
especially when the throttle is opened suddenly, the shape and the size of
emulsion tube
T -
Fig. 9 - become two extremely important design
factors: in fact, with engine idling in tube
T
and in associated well
P there is a certain amount
of fuel whose level, owing to capillary action, is often at the same height
as the level in float chamber.
When the throttle is opened, even a slight vacuum (a few mm water column)
will be sufficient to draw fuel from well
P and prime the mixture supply from the main
circuit.
In brief, there are two systems without moving parts that are
generally adopted to ensure smooth engine operation during throttle opening
stages: - One or more transition orifices, and -
A
reserve of fuel in well
P.
In spite or the design features described there are cases in which an
accelerating pump must be used to inject an additional amount of fuel at
every quick opening of the throttle.
Generally, the accelerating pump is incorporated in carburettors when:
-
Venturi diameter is greater than 22-24 mm
-
A single carburettor feeds many cylinders
-
The application is for sports engines.
The quick opening of the throttle may cause a temporary leaning out of
the mixture strength as a result of the faster rate at which air is swallowed
with respect to the carburettor.
This depends on the different densities
and circuiting of the two fluids inside the carburettor. Generally, best
results are accomplished if the injected fuel is directed against the edge
of the throttle valve that does not affect the operation of transition orifices.
The mechanically-operated pump may be either of the plunger or diaphragm type,
see
Fig. 12-A and
Fig. 12-B.
With the plunger pump -
see
Fig. 12-A -
when the throttle is opened plunger
Sp is pushed down by
spring
2 and compresses the fuel beneath it: suction valve Va thus closes
and the fuel, via delivery valve
Vm which is lifted from its seat, flows
partly through pump jet
Gp and partly back to float chamber via pump drain
jet
Gsc.
When the throttle is closed the plunger travels back up compressing
spring
2 and sucks in fuel through valve Va and
jet
Gsc.
With the other type of pump - see
Fig. 12-B -
a diaphragm replaces the plunger but operation is
practically the same. The importance of jets
Gp
and
Gsc will be explained later on.
d) Starting device or choke
This device completes the modern automatic carburettor in its simplest form.
When a cold engine is started, and especially at low ambient temperatures,
the following phenomena take piace:
-
Too weak vacuum acting on jets and developed in intake manifold because
the starter-cranked engine turns very slowly, for various reasons,
namely, about 70 to 150 rpm.
-
Inadequate mixture supply from the idle speed circuit and no mixture at
ali from the main jet, owing to the extremely low vacuum.
-
Fuel condensation on intake manifold and cylinder walis as a consequence of
the low vacuum and temperature. The cylinders receive a lean and poorly
blended mixture containing a high percentage of fuel which is stili in the
liquid state and hence the charge is difficult to ignite.
To ensure prompt starts and smooth operation during engine warm up
the carburettor must supply a rich mixture and this is obtained by
a special device known as the "choke". Once the engine reaches its
normal rated operation temperature the choke must be excluded.
Manual choke of the auxiliary carburettor type
This starting device consists of an auxiliary carburation unit fed directly from
the float chamber and which is cutin or out, with throttle set in idle speed position,
by a separate hand control. As shown in
Fig. 13, when
valve
3 is opened the depression
present downstream of the throttle communicates with fuel reserve
well
4 - via ducth
1 - and hence with jet
Gs.
The mixture supplied by this circuit and leaned out by the air entering through
jet
2, allows engine to start and rev-up to an
adequate power during the warming up stage.
This type of starting device is provided with a simple blanking valve but the
system may be improved by adopting a progressive-action valve which permits
the desirable "graduation" in choke operation.
Manual choke of the shutter valve type
With this system (see
Fig. 14)
the auxiliary carburettor described
earlier is replaced by a shutter (or strangier) valve
Fs positioned offset
with respect to barrel centreline and upstream of
Venturi
D.
During the
starting stage -
Fig. 14-A -
shutter valve is closed while throttle
valve
F is slightly open - fast idle position - through a lever
linkage control.
As will be readily apparent, the vacuum produced by
the cranked engine is no longer confined to the area downstream of
throttle
F as occurred in the previously described system but now
influences the whole area beneath shutter valve, including
Venturi
D and nozzle
S.
Once engine has started, the vacuum around
nozzle
S increases and the resulting
mixture would be excessively rich
but at the same time also the force tending to open shutter
valve
Fs increases; this is why the
latter valve is not rigidly connected
to choke contro[ lever linkage but through the intermediary of a calibrated
spring M so that valve
Fs may open to keep
the depression at the specified value.
Once engine is warm, shutter valve
Fs must be set back to its vertical
position -
Fig. 14-B - namely, the
"choke" control must be excluded.
For improved engine warm-up operation also a pneumatic overchoking or
antiflooding device -
Fig. 15
- is sometimes used. The vacuum downstream of
throttle
F increases once engine has started
and by acting on diaphragm
A it
overcomes the resistance of spring
2;
as a result, valve
Fs opens against the
opposing action of the choke spring (not shown) to a position governed by the
setting of adjusting screw
3.
As long as the engine keeps running, shutter valve
Fs may open further but cannot close. One other shutter valve type of choke
is shown in
Fig. 16;
during engine starting strangler
Fs
remains
shut as its plate incorporates a poppet valve
1 which governs the
amount of incoming air according to engine requirements.
Over the auxiliary carburettor arrangement the shutter valve choke offers
the advantage of obtaining prompter starts and higher power outputs
from the engine at low temperature.
Automatic choke
To make driving easier, prevent misuse and avoid leaving the choke in
even after the engine has reached its rated operation temperature, some
carburettors have been fitted with an automatic choke which is independent
of driver's will.
The automatic choke contro], also shown in the colour chart, is ensured
via a temperature-sensitive element (bi-metal spring or expanding capsule)
which, with engine cold, takes care of inserting the choke, be the latter of
the auxiliary carburettor or offset shutter valve type.
Choke cut-out is controlled by the heating of the temperature-sensitive
element: it receives heat from exhaust manifold heated air, engine cooling
system water or an electric resistor wired to the ignition circuit.
The only action which the driver is normally called upon to take for choke
insertion is to depress fully and release the accelerator pedal before starting
the engine; for this reason, controls of this kind are often referred to as
semi-automatic.
Referring to the schematic representation of parts involved in
Fig. 17 a description is
given in the following paragraphs of the choke insertion, starting, acceleration
and choke disinsertion stages.
Choke insertion - with engine cold, bi-metal spring
B shifts
pin
1 and lever
2,
in one with lever
3, thus moving offset shutter
valve
Fs into closed position: this action occurs when
the driver, before starting, depresses fully and then releases the accelerator pedal.
This preliminary action by the driver is indispensable to move away from
cam
4 screw
5 (carried on
lever
6) via rod
7 connected
to accelerator lever
8: in fact, unless
screw
5 is moved out of the way, bi-metal
spring
B cannot rotate lever
3
which drags along also fast idle cam
4 through
spring
9.
Before starting the engine, shutter valve
Fs must
be closed and screw
5
must rest against cam
4 to give
throttle
F the pre-set fast idle opening.
Starting and acceleration - Once engine has started,
the vacuum beneath throttle
F increases and gains enough
force to shift diaphragm
D and rod
10
the amount allowed by the setting of the mixture weakening
screw
11 - pneumatic antiflooding; the shift of
rod
10 causes a partial opening of shutter
valve
Fs to suitably proportion mixture strength to
engine warm-up requirements, by overcoming the force of spring
M
and bi-metal spring
B.
If the accelerator pedal is pressed lightly and enough to move screw
5
away from cam
4 the latter - via spring
9
- will be turned through the same angle which the shift of rod
10
had earlier caused lever
3 to make.
In case accelerator pedal is released, screw
5 will abut against
cam
4 in another location, the cam now being set for a reduction in
fast idle rate.
Should the accelerator pedal be depressed more forcibly, the vacuum beneath
throttle
F will decrease, spring
M
sets back rod
10 and the opening of shutter
valve
Fs will be governed by bi-metal
spring
B alone.
Should the starting be prevented by an excessively rich mixture, by depressing accelerator pedal
fully in throttle
F will open completely and, through
rod
7 and the lug on lever
6, it will
rotate cam
4 and lever
3 thus causing
shutter valve
Fs to open of a given amount: at this point, by cranking
with the starter motor it will be possible to lean out the mixture first and then repeat the
starting operation as described above.
Choke disinsertion - With engine running, the heat produced by
heater
R is conveyed to bi-metal spring
B
which gradually deforms and reduces the force tending to keep shutter
valve
Fs closed: this reduces mixture richness and the fast idle rate.
Once the rated temperature is reached, bi-metal spring
B positions shutter
valve
Fs vertical and rotates cam
4 until
it no longer contacts screw
5: throttle
F
may thus return to its normal idle speed setting governed by idle speed adjusting
screw
12.
Modern Carburettors Features
Some basic carburettor devices have been described in the preceding paragraphs but there are also a
few other particular systems which have found wide application in current automotive engineering
and are worth being illustrated.
Auxiliary (or secondary) Venturi
The purpose of this second Venturi is to boost the depression existing in the main or primary Venturi
and to improve the mixing of fuel with the incoming air.
In some of the earlier illustrations this
device is represented as a small Venturi surrounding spray nozzle
S - for instance,
Fig. 16 - with
its lower edge terminating in the narrower section (or striction) of the main
Venturi
D.
Multi-barrel carburettors
To improve engine performance at full power, the trend in automotive design is to adopt more
than one carburettor on the same engine so that each carburettor or barrel feeds a limited number
of cylinders, or even a singie cylinder: in this way, volumetric efficiency (or combustion chamber
charge) is improved with the added advantage that the fuel feed to each cylinder, or group of
cylinders, is unaffected by the intake stroke of the others, thus ensuring a more uniformly blended
mixture distribution.
This same result could be achieved by adopting a number of single-barrelled carburettors but for
evident reasons of simplicity and control positiveness, the carburettors with two or more barrels
(or throats) incorporated in a single body casting are preferred, often having a single constant-level
float chamber in common for fuel supply.
An important feature is the method adopted for the opening
control of the throttles which may be either of the differential or the synchronised type.
The direct type (mechanical) differential contro] is shown in
Fig. 18: accelerator
lever A is integra] with the throttle F1 which is opened first
(hence, primary throttle) and when its opening reaches 2/3 the maximum setting,
intermediate lever
L begins to open
throttle
F2 (secondary) and completes the opening within
the remaining part of its travel.
The primary barrel - often smaller than the secondary in diameter - is adjusted to provide an
economic mixture strength for part-load operation whereas the secondary barrel is adjusted for
full power and acceleration performance.
The secondary barrel control may also be of the pneumatic type, that is, obtained through a
diaphragm actuated by the vacuum by-passed from the primary throat. -
Fig. 19.
Upon opening of the primary throttle
F1 the vacuum in
main Venturi
D is ducted to the chamber
of diaphragm
P through passage
1.
If throttle
F1 is totally open,
lever
L1 is lowered and
frees lever
L2 which is connected (via a link rod)
with diaphragm
P: in this case,
the vacuum acting on the diaphragm and opposed by spring
M,
opens throttle
F2 gradually and in accordance with the amount of air
drawn in by the engine.
Upon closing of throttle
F1 the lever linkage shown ensures
the prompt closing of throttle
F2.
This type of pneumatic control finds wider
application on engines which have the possibility of operating, at full power,
over a wide rpm rate range.
The intake manifold used in conjunction with differential carburettors has a single cavity
into which arrive the two carburettor ducts.
The synchronised contro] may be obtained by fitting the throttle valves on the same
spindie or on separate spindles interconnected by two identica] toothed sectors.
To ensure best engines performance, the opening angles of the two throttles must be the
same at ali times, whatever the position of the accelerator.
The synchronised control is usually adopted when each carburettor barrel feeds one
cylinder or a group of cylinders, independentiy of the others.
In this case the intake manifold is provided with a separate tubing for each carburettor
barrel, connected to the cylinder or group of cylinders involved.
At times the separation of the ducts is limited by a common channelling known as the
"compensating type".
Mixture strength control devices
As described earlier (see
Fig. 3-4-5)
for maximum engine efficiency and best use of the fuel, the mixture
strength must be proportioned to engine requirements established by both laboratory
and road tests.
With wide open throttle the mixture must be slightly rich for maximum power and good
engine life, whereas with part-open throttle, hence part power, the mixture may be
leaned out with ali the ensuing advantages of greater economy and exhaust gas toxicity
reduction.
If a carburettor barrel supplies fuel to just one or two cylinders, the fluctuations
in incoming air flow rate already produce the necessary weakening in mixture strength
during part-throttle operation.
But often it becomes necessary to provide the carburettor with additional devices for
the special purpose of adapting it to engine demands under any and ali conditions.
One such arrangement - called overfeeding device - consisting of a mixture control system
without moving parts is shown in
Fig. 20.
It is a separate circuit, in parallel with and independent of the main circuit,
consisting of a fuel jet
1, an
air jet
2 and a
mixture jet
3.
The fuel, drawn from the bowl and metered by jet
1,
emulsifies with the air coming in through jet
2
and the mixture thus formed - via calibrated bush
3 -
is sprayed into channel
4
in auxiliary Venturi, just above nozzle
S.
The supply from this circuit serves mainly to enrichen the mixture to offset the greater
amounts of air flowing both when throttle is partially or totally open.
Another quite similar system is shown in
Fig. 21:
in this case, however, there is no emulsioning air and the supply of fuel takes piace
through a special spray tube Ts.
Fig. 22
shows a system adopted to weaken the mixture
under part-open throttle conditions. It consists of a valve
Vsm operated by the throttle
spindle and serves to biank - at wide-open throttle - an additional air outlet in the
carburettor main feed circuit.
At part-open throttle, instead, there is an addition of air (left, see arrows) in the
well located below air corrector jet
Gf, valve Vsm being open.
Fig. 23 (A and B) shows a special valve,
in two versions for mixture enrichment control either when the throttle is part-open
(see
A) or wide-open (see
B).
Control is by the vacuum existing in the intake manifold.
Fig. 23-A,
part-load mixture enrichment: the vacuum, ducted from orifice
1
beneath the throttle, arrives in the chamber above diaphragm
2
which is lifted against the action of spring
3.
The fuel drawn from bowl V flows through the valve seat
(see arrows) is metered by jet
4 and then issues via the channel
above spray nozzle
S.
With wide-open throttle, the depression is not
strong enough to overcome the force of spring
3 and the valve
remains closed (position shown by the chain-dotted outline).
Fig. 23-B,
full power mixture enrichment: the vacuum action is
the same as described above but valve operation is reversed.
At part-open throttle, diaphragm
2 is in raised position, as shown,
and the valve is in this case closed thus preventing any passage of fuel.
With wide-open throttle the vacuum cannot keep the diaphragm
2 raised and
thus the valve remains open (position shown by the chain-dotted outline).
Fig. 24 shows a
mechanically-operated full-power mixture enrichment system.
With wide-open throttle, the plunger of accelerating
pump
Sp is at bottom stroke and causes
taper valve
Vp to remain open.
Via valve Vp the fuel from pump barrel arrives at jet
Gpp
thus providing a supply in parallel with main jet
G.
With partopen throttle, as shown in the figure, valve
Vp
remains closed and no additional supply of fuel is had.
A similar circuit may also be adopted for the diaphragm-type accelerating pump.
Dust-proof carburettors
Current practice is to connect ali air inlets and outlets of the carburettor -
such as air bleed jets, float chamber vents, choke air jet, etc. - to the
"clean" side of the air cleaner: this leads to advantages in carburettor interior
cleanliness, silent running, less influence of filter dust build-up on fuel consumption,
air pollution, etc.
There are, however, also two notable drawbacks: starting difficulties when engine
is hot due to an accumulation of evaporated fuel (percolation) and the engine
"hunting" effects - rather complex and not utilisable to the best advantage in
all cases - on mixture strength.
For this reason the fully dustproof carburettor cannot be adopted in some applications.
Needle-valve spring dampers
To improve the maintenance of the correct fuel level in float chamber, a
spring-dampened type of needle valve has found wide application - see
Fig. 25.
This arrangement proves beneficial with carburettors subject to marked
vibrations, on engines with few cylinders and high rpm rates.
In
A and
B
(
Fig. 25) are two
sections of the needle valve showing its incorporated damper consisting of a spring
and bali.
A solid needle is shown in
C.
Sometimes it is better to have the needle controlled directly by the float to prevent
"bindings" resulting from impurities or gums in the fuel.
With some designs, the taper seat of the needle valve is made of a non-metallic
material, for instance, synthetic rubber.
Idle shut off solenoid
A solenoid incorporated into the idle circuit to cut off fuel flow when the ignition
is switched off.
Its only purpose is to prevent the engine from running on.
Sometimes the solenoid pin operates upon the jet, sometimes it is located elsewhere in the circuit.
Slot progression
Very late carburettors have a slot to provide progression onto main circuit instead of a
series of holes. This gives finer control over mixture strength.
Anti-stali device
Also referred to as low vacuum enrichment or
LOVE device; a vacuum controlled
accelerator pump.
At idle, if manifold depression drops below a certain point, the spring behind a diaphragm will
overcome the vacuum and inject a pulse of fuel to prevent stalling.
Throttle kicker
Provides an increase in idle speed under specific load conditions.
For example air conditioning, auto transmission, power steering.
This is obviously not necessary if a stepper motor is fitted to the carburettor.
Float chamber vent solenoid
This solenoid is fitted into the carburettor's top cover.
During normal driving conditions the carburettor is vented into the air cleaner
(referred to as 'internal venting').
When the vehicle is stationary, after reaching full operating temperature,
the solenoid opens an external vent to reduce the build-up of vapour
which would cause hot starting problems.
Stepper motor
A 4-phase electronic motor which controls the throttle position at idle, and therefore engine speed, under ali circumstances.
Main Functions
- Contro[ the engine speed during warm-up period.
- Control of engine speed under ali conditions of load,
ie with headlights, wiper motors, air conditioning,
heater, radio, on, etc.
- Complete closure of throttle during deceleration for
maximum economy and minimum emissions.
- When the engine is turned off the plunger retracts
completely to prevent running on.
- During hot soak the plunger extends fully to vent the
inlet manifold.
- The Stepper Motor is controlled directly by the electronic
control unit (ECU) which is receiving inputs from sensors
in the engine.
Fuel feed system
For space and safety requirements, in current design feed systems
the fuel is sent from tank to carburettor by an engine-driven
mechanical pump -
Fig. 26-A
- or an electric pump -
Fig. 26-B -
located in proximity of the fuel tank.
Referring to
Fig. 26-A,
cam
1 actuates - via
rocker
2 and
rod
3 - the plates holding
diaphragms
5/6:
diaphragm
5 provides fuel tightness on engine side
while diaphragm
6 pumps the fuel.
In the figure, the pump is shown during the delivery stage with
intake valve
7 closed and
delivery valve
8 open: air
chamber
9 serves to stabilise the flow rate.
Upon further rotation, camshaft
1 causes the lowering of the
diaphragms, this in turn closes the delivery valve and opens the
intake valve for the arrival of new fuel from the tank.
Spring
4 is rated to establish the maximum delivery pressure value,
also known as self-regulating pressure (0.2-0.3 kg/sq.cm.).
Fig. 26-B shows an
electric pump; item numeration is the same for equivalent parts in
A and
B.
During the delivery stage, plunger
S travels upward under the action of
spring
4,
magnet
M causes
contact
C to "make",
thus supplying battery current to coli
B.
The magnetic circuit pulls down plunger
S
(intake stroke) but also causes contact
C
to "break" this way, spring
4 again pushes
up plunger
S for a new delivery stroke.
Fig. 27 is a graph showing
the flow rate delivery pressure data versus engine rpm -
referred to a mechanically-operated fuel feed pump - and
consumption curve
C of
the engine on which the pump tested was used.
In addition to ensuring a fuel delivery always greater than the amount used up by the engine,
the lift pump must provide the following:
- Quick priming at low engine rpm (starting stage)
- Delivery pressure within the specified limits
- Effective heat insulation for satisfactory operation during the hot season
- Silent running.
To prevent the disadvantages ensuing from the overheating of mechanical pumps, the system shown in
Fig. 28 is sometimes adopted: this type
of circuit serves to send the fuel vapours produced
in pump or lines back to the fuel tank.
